README.TXT   CC-SURVeyor 2.00    Shareware Version    January 1, 1988
     
     CC-SURVeyor is a COGO program for civil engineers and land surveyors,
     that interfaces with Generic CADD by transferring batch files both
     ways.  It allows points, point numbers and lines to be created from
     maps of record or legal descriptions, so that Generic CADD could
     quickly load the boundary, allowing the civil designer to  get started
     with building layout or lot layout within CADD.  It includes traverse,
     inverse, sideshot, bearing and distance intersection routines, area,
     inscribe curve, rotate/translate/scale, lot summary, radial stakeout,
     predetermined area, and perpendicular and parallel offsets.
     
     A set of topo utilities allows reduction of field notes for EDM or
     total station topo, with transfer of points, numbers, elevations and
     descriptions to Generic CADD.
     
     This shareware version is complete in every way, except that point
     numbers are limited to 1 thru 99.  The manual on the diskette is
     complete and accurate with that one exception.  The files distributed
     in this version are otherwise identical to the registered version.
     You are free to use, copy and distribute this program, as long as
     copies contain all the files herein, and no more than a $6 diskcopy
     fee is charged.  If you like CC-SURVeyor and wish to register it, a
     $75 contribution will entitle you to:
     1.   A new diskette with the latest version, including 999 point
          storage capacity and excluding the shareware entrance screen.
     2.   Full support by mail.
     3.   Subscription to CCNEWS, an electronic bulletin board newsletter
          with the latest news of civil engineering and surveying shareware
          and public domain software, including news of CC-SURVeyor
          upgrades.
     
     
     SYSTEM REQUIREMENTS AND INSTALLATION
     
     This program was developed and compiled with QuickBASIC, version 3.0
     and should be compatible with any IBM PC compatible using MS-DOS 2.11
     or later.  An 8087 coprocessor is not required.
     
     To install CC-SURVeyor, simply copy the *.EXE files (CC-SURV.EXE,
     CC-TOPO.EXE, BRUN30.EXE) onto the diskette or hard disk subdirectory
     of your choice.  Type "CC-SURV" to start it.  Neither CC-TOPO nor
     BRUN30 are intended to be run alone.  CC-TOPO is an overlay for the
     Topo submenu, and BRUN30 is the MicroSoft run time module that
     must be present to run programs compiled with QuickBASIC 3.0.  If you
     already have BRUN30 on your hard disk, you don't have to install it
     again as long as it is in the current PATH when CC-SURVeyor is run.
     
     FILES ON THIS DISKETTE
     
     README.TXT    This file you are reading
     CC-SURV.TXT   The program manual
     CC-SURV.EXE   The CC-SURVeyor program
     CC-TOPO.EXE   The TOPO/FIELD submenu
     BRUN30.EXE    QuickBASIC run-time module
     DEMO.CCC      Coordinate file created by CC-SURVeyor
     DEMO.TXT      Generic CADD batch file created by CC-SURVeyor
     CONFIG.FIL    Configuration file for Generic CADD.  See CC-SURV.TXT
     SURV.FNT      Font file for Generic CADD with surveying symbols
     VIDEO.MNU.    Video menu for Generic CADD with added menu items.
     
     You may print out CC-SURV.TXT by typing "COPY CC-SURV.TXT PRN" from
     the A> DOS prompt.  Don't worry about the left margin or page breaks,
     as they are taken care of in the TXT file.  Just be sure your printer
     is set to top of form before printing, and you have at least 34 pages
     of paper ready.